Improvement of dielectric breakdown strength and energy storage performance in Er2O3–modified 0.95Sr0.7Ba0.3Nb2O6-0.05CaTiO3 lead-free ceramics

In this study, 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃-x wt% Er₂O₃ ceramics (SBNCTEx; x?=?0–5) were synthesized using traditional solid-state method, and we investigated the microstructure, energy storage properties as well as the relationship between dielectric breakdown strength and interfacial polarization. As compared with pure 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃ ceramics, the Er₂O₃ dopants suppressed the grain growth of SBNCTEx, and the doped ones showed the dense microstructure. The secondary phase was found for x?≥?1 according to the EDS results, and the influence of the secondary phase on relative dielectric breakdown strength has also been studied. The dielectric breakdown strength increased from 18.1?kV/mm to 34.4?kV/mm, which is good for energy storage. The energy storage density of 0.28?J/cm³ and the energy storage efficiency of 91.4% were obtained in the SBNCTE5 ceramics. The results indicate that SBNCTE ceramics can be used as energy storage capacitors.     

基于张量分解融合RGB-D图像的物体识别

为了充分利用RGB-D图像的深度图像信息，提出了基于张量分解的物体识别方法。首先将RGB-D图像构造成一个四阶张量，然后将该四阶张量分解为一个核心张量和四个因子矩阵，再利用相应的因子矩阵将原张量进行投影，获得融合后的RGB-D数据，最后输入到卷积神经网络中进行识别。RGB-D数据集中三组相似物体的识别结果表明，利用张量分解融合RGB-D图像的物体识别准确率高于未采用张量分解的物体识别准确率，并且单一错分实例的准确率最高可提升99%。     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

电喷雾质谱法示踪钨回收过程离子的转化路径

将环隙式离心萃取器(ACCs)与电喷雾飞行时间质谱(ESI-TOF-MS)相结合，在线监测了回收过程中的钨萃取行为(宏观)和钨形态的转化路径(微观)，发现宏观萃取反应和微观离子形态转化同时发生并相互补充。伯胺N1923萃取钨在144 s内即可达到萃取平衡，萃取率高达98%以上，同时，酸钨比n(H)/n(W)是一个关键变量，当酸钨比n(H)/n(W)=2.4时，全流程钨回收率超过93%。最后，得到了基于钨形态监测的萃取机理，同时，减少原料液中W1含量，增加W10含量，可有效提高钨回收效率。     

一种基于小字典不对等语料的跨语言词嵌入方法

双语词嵌入通常采用从源语言空间到目标语言空间映射,通过源语言映射嵌入到目标语言空间的最小距离线性变换实现跨语言词嵌入。然而大型的平行语料难以获得,词嵌入的准确率难以提高。针对语料数量不对等、双语语料稀缺情况下的跨语言词嵌入问题,该文提出一种基于小字典不对等语料的跨语言词嵌入方法,首先对单语词向量进行归一化,对小字典词对正交最优线性变换求得梯度下降初始值,然后通过对大型源语言(英语)语料进行聚类,借助小字典找到与每一聚类簇相对应的源语言词,取聚类得到的每一簇词向量均值和源语言与目标语言对应的词向量均值,建立新的双语词向量对应关系,将新建立的双语词向量扩展到小字典中,使得小字典得以泛化和扩展。最后,利用泛化扩展后的字典对跨语言词嵌入映射模型进行梯度下降求得最优值。在英语—意大利语、德语和芬兰语上进行了实验验证,实验结果证明该文方法可以在跨语言词嵌入中减少梯度下降迭代次数,减少训练时间,同时在跨语言词嵌入上表现出较好的正确率。     

Selective Coating of SnS on the Bio‐Inspired Moth‐Eye Patterned PEDOT:PSS Polymer Films

A new strategy for the selective coating of tin sulfide (SnS) on the surface of moth‐eye patterned (MEP) conducting polymer film is studied by considering the optical properties of the antireflective moth‐eye pattern and flexibility of polymer films. The semiconductor SnS is selectively coated on the surface of MEP microdomes of poly(3,4‐ethylenedioxythiophene) poly(styrene‐sulfonate) (PEDOT:PSS) film. The SnS coated MEP film is obtained by using pore selectively SnS thin layer functionalized polystyrene honeycomb‐patterned porous (HCP) film as a template. Aqueous PEDOT:PSS solution is poured on the SnS functionalized HCP films and detached for the fabrication of SnS coated MEP films. The films show a satisfactory photo‐responsive property under solar stimulated light illumination due to the antireflective MEP structure of PEDOT film and homogenous SnS coating on the surface of the conducting polymer.     

Controlling thickness to tune performance of high-mobility transparent conducting films deposited from Ga-doped ZnO ceramic target

Structure modification has been found to tune significantly the transparent-conducting performance, especially mobility and conductivity of hydrogenated Ga-doped ZnO (HGZO) films. The strong correlation between film thickness and mobility of the films is revealed. The mobility increases quickly with increasing the thickness from 350 to 900 nm, and then tends to be saturated at further thicknesses. A higher mobility than 50 cm²/Vs can be achieved, which is an extra-high value for polycrystalline ZnO films deposited by using the sputtering technique. The thickness-dependent mobility originates from scatterings on grain boundaries and dislocation-induced defects controlled by thin-film growth. Based on the Volmer-Weber model, an expansion model is built up to describe the thickness-dependent crystal growth of the HGZO films, especially at the thick films. As a result, the 800 nm-thick HGZO film obtains the highest performance with high mobility of 51.5 cm²/Vs, low resistivity of 5.3 × 10^?4 Ωcm, and good transmittance of 83.3 %.     

Improved Corrosion Resistance of Selective Laser Melted Ti–5Cu Alloy Using Atomized Ti–5Cu Powder

The different types of metal powder used for selective laser melting(SLM) process would cause distinct corrosion behavior due to the uniformity of the obtained microstructure.The SLM-produced Ti–5Cu alloy using atomized Ti–5Cu metal powder(SLMed Ti–5Cu) in this work reveals a relatively uniform microstructure with overwhelming acicular α/α′ phase and shows great advantages on corrosion resistance compared with the SLM-produced Ti–5Cu alloy using the mixture powder(SLMedM Ti–5Cu).The effect of the micro-galvanic cells decreases due to the undetectable Ti_2Cu phase in the microstructure of the SLMed Ti–5Cu.An apparent passivation behavior was observed for SLMed Ti–5Cu instead of severe pitting phenomenon for the SLMed-M Ti–5Cu.The charge transfer resistance of SLMed Ti–5Cu in this work is 10.09 ± 2.63 MΩ cm~2, which is significantly higher than that of SLMed-M Ti–5Cu(4.76 MΩ cm~2).The above result indicates the atomized Ti–5Cu powder plays an important role in the formation of the uniform microstructure of SLMed product, thereby enhancing its corrosion resistance in Hank's solution at 37 ℃.     

Different hydrothermal corrosion results between two sides of sodalime float glass and the possible corrosion mechanism

Sodalime float (SF) glass is widely used in our societies and industries. Hydrothermal corrosion method is one of the effective ways to prepare a superhydrophobic glass, but there is still lack of knowledge about hydrothermal corrosion behavior and mechanism of SF glass. We have hydrothermally treated SF glass at 180 °C for different time, and tried to reveal the aqueous corrosion process of SF glass. We have characterized the morphologies and chemical compositions of samples, and found that (1) the two sides of SF glass have different corrosion resistances, and (2) a multilayer structural coating with a nanoflake layer (Mg-rich gel layer), a nanowire layer (Ca-rich gel layer), and a porous layer (etched layer) is formed on the air-side of SF glass. Based on the experimental results, we have proposed an aqueous corrosion mechanism of SF glass. The insights of the hydrothermal corrosion behaviors and mechanism provide helpful guidelines to glass surface structural control and functionalization.     

Fabrication strategies and application fields of novel 2D Ti3C2Tx (MXene) composite hydrogels: A mini-review

Ti₃C₂T_x (MXene), a new kind of 2D ceramic nanosheets, is receiving more and more attention in the fields of medicine, biology, energy, electronics, etc. However, the preparation and application of MXene in hydrogel is still in its infancy period. Here, we review the latest progress (after 2018) related to MXene hydrogels in time. Aiming at the key issue of the dispersion stability of MXene in hydrogel systems, the preparation strategy, mechanism, advantages and disadvantages of MXene hydrogels are sorted out in detail, and the potential application prospects of MXene composite hydrogel are introduced. Finally, future viewpoints are put forward for the dispersion stability challenges that need solving in the design of MXene hydrogel.